July 5th, 2010
Kitchen and dining room are two rooms that “comprehensive” or at least close. Kitchen as a space to process raw materials in a variety of cuisines, in fact perfectly juxtaposed with the dining room as the room had food.
In architecture, the kitchen and dining room are side by side. That is, among others to facilitate and accelerate the process of preparing the dishes to the table diverse. The kitchen is a “blend” unlimited dining and other rooms. There is also a stand-alone occupy a separate space. This location should be considered when you are decorating the kitchen and dining room.
Read more »
May 5th, 2010
Windows serve several very different roles in a house: a view of the exterior, allowing sunlight to enter, can provide fresh air, and block the flow of heat. The relative importance of these functions varies according to climate and location of the windows of the house. For example, residents of Minnesota will most likely be interested in passive solar heat gain and therefore want windows that transmit a large amount of
solar heat, especially on the south side of the house. Florida residents, however, will probably be more concerned with blocking the solar heat gain (see Chapter 7 for more information on passive solar heating).
Next to the amount of insulation in the house and seal on the house, the selection of windows and doors have the greatest impact on energy use for heating and air conditioning. Fortunately, this is where some of the most significant advances have been made in building technology over the past decades. The best windows now have up to four times the insulation value of the best windows in the 1970s.
Read more »
May 5th, 2010
Heat flows by three mechanisms: conduction, convection and radiation.Conduction is moleculetomolecule transfer of kinetic energy, a molecule is converted into energy, and in turn energizes adjacent molecules. Castiron handle skillet heated by conduction through the metal. Convection is the transfer of heat by the physical movement of molecules of energy from one place to another – for example, warm air rises, or a heating system using FORCEDOS fans to push hot air around a house. Radiation is the transfer of heat through space via electromagnetic waves (radiant energy), a fire can get warm, even in windy conditions between you and the fire, because radiation is not affected by the air.
With the buildings, the heat flow is measured in a number of different ways. R-value describes a material or the resistance of a heat development component higher the R value flow.The of a material, the better to resist heat loss or heat gain. Ufactor is a measure of how much heat flows through a material reality in a given time and given a certain difference in the temperature of a material side to the other – the heat always flows from warm to cold side. Ufactor R value and are the inverse of each other: U = 1 / R. For example, if a wall has an average R value of 15, the Ufactor for the wall would be 1 / 15, or 0.067.That Ufactor tells us how many BTU of energy will move through one square foot of wall every one degree Fahrenheit temperature difference between wall
(0.067 Btu/ft2 ° F · · h). The materials are very good to resist heat flow (high R-value, low Ufactor) can serve as insulation materials.
May 5th, 2010
There are several ways to hire a designer home. The traditional approach is to hire an architect to design your house, then hire a builder to build it. Thus, the architect usually stays involved with the project from start to finish, helping to find the builder and make sure the house is built as specified. Usually pay the architect a fixed percentage of the total project cost to cover design work. Depending on the specific contract, may pay more for the management of the project if the architect offer this feature.
Another possibility is hiring a designbuild company that will handle both the design and construction. This can be a huge advantage with a green house, because you can be sure that these functions are integrated. The design is done with special attention to the ease and efficiency with which to build. When it comes to the construction of the house, the necessary modifications can be easily treated as designers and builders are part of the same company. For design work, companies either charge by the hour designbuild, or charge a fixed percentage of the total project cost. For construction work, which often charge on a costplus, charge the actual cost of materials and labor plus a fixed profit level. Most designbuild companies are small, with fewer than 25 employees.
May 5th, 2010
During this mild steel is known as a material for the roof frame house. In fact, mild steel can also be applied to other things, such as the closing frame carport. Mild steel name certainly is not foreign in your hearing. This material is widely used as roof frame houses, offices, and other buildings. Observations conducted last year showed that not less than 90 percent of the housing project being built at that time using lightweight steel roof truss.
Examples of the use of lightweight steel roof truss, instead as the latter is widely seen as the framework cover carport. Physical shape in the form of bars makes it easy to be adopted to create similar forms pergola or other forms. Designs can dikreasikan, to be combined with various types of roof coverings. Profile of a solid mild steel but easily shaped design allows the homeowner to taste his carport. Curved wall is another example of carport designs. Wall material using C7575 and Trimdek Crimp Curve (s), while material from Lysaght roof made curved.
Read more »
